Bedroom Carpet Facelift and Upgrade

Oct 22, 2016.  Our coach originally came with an off white sheet vinyl with gold veining.(guess they wanted to match the jazzy mirrors with gold veining which we actually adore!) However the vinyl is a bit tired and having a cozy carpet to step on in the early morning wake up is really welcomed. So we decided to do a carpet facelift.  The previous owner can cut and fitted an off-white Berber rug remnant in place. It was in decent shape and clean. What you see are just shadows. But the transition from kitchen to rug was never completed with any threshold etc. And you also had to be careful not to catch or chip the raw vinyl edge.

So we used the remnant for our pattern. Luck would have it, Home Depot ( yes about our 8th HD trip in two weeks… uuugh) had a 26″ w oriental runner sold by the foot. That was the exact width we needed! And the color will go fine with my Spring 2017 decor refit.  That is secret for now.  Our length needed was 74 1/2″ and this provided enough to once again notch out the moulding door jam at the bathroom transition.  The door in the bathroom was plenty high so this was deemed not a problem for a carpet install right into and even with the door threshold. In fact the BR door is very high clearance off the ground. I know the ’72 brochure I have seen said Avions came with “deep pile quality shag carpet” .  I suspect just cause our owners chose vinyl the production line was not bout to change their jig for one coach.  Hey we ARE talking the 70’s folks and I remember shag all over our house!  But really? In a camper? Yikes! The dirt build up had to be disgusting.  I believe our first owners voted for vinyl from the start. Reason we think so is because the white with gold veins is sheet vinyl and runs clearly under all bathroom cabinets, under beds, under kitchen cabinets. Suggesting that it was put down first during the coaches construction and all else was installed on top.

Anyway, I digress. Sorry. Back to our project. Here we are measuring and cutting out the notches to fit BR door moulding. Remember to lay your pattern piece same facedown direction as your new carpet!

Remember if you ARE using an existing carpet that you have both of them facing in the same direction on the table…not pile to pile (like I almost did) because notches may not be identical from side to side when you flip your new carpet right side up. Ours notched areas were not  identical and so your cuts will not be correct if you screw this up.  Our carpet cost us 26.00, the two oak thresholds were $11 each, plus stain which we had.  1/4 inch carpet pad was $8.50 again a remnant cast-off from a local carpet store.

The new Carpet was cut first with a box cutter. (Could not find our carpet cutter). Then little final trims retire able to be done in coach with sturdy household scissors which gave us more control for tiny slices to ensure perfect fit at doorway. I also recommend leaving any of the edge building threads long. Wrap them to the back of your new carpet and tape them down with gorilla tape. This prevents any short traveled threads from. Showing or eventually popping loose and showing on the top side.

Below is carpet pad being trimmed and pieced to fit. Note orig gold veined Vinyl flooring. Not bad for 44 yrs old!

You could butt together and tape any pieces of padding. we did not bother on such a small seam. Larger seams should be taped to hold in place well.

Below are final adjustments and oak transition thresholds screwed in place. Be careful not to screw any deeper than you have to. Be especially careful in BR to bedroom areas. There have been more than one Avioner who ended up using too long a screw and drilled into a holding tank by mistake! Total bummer!

Below the thresholds are being screwed down You want to be sure you grab enough of the carpet to keep it secured. Our entire dining and kitchen area subfloor and vinyl had been replaced in last six yrs with 3/4″ marine plywood so our carpet and kitchen vinyl is now even. It was not before. Here is bathroom transition.

Here is kitchen transition. Sure does feel nice under foot! Fits perfect under the under bed cabinets and drawers no problem. We did have to take the heat vent cover on curbside under my twin bed and screw back in place after carpet was down.

The finished project! Looks and feels grand. Lucky for us HD also had an already found piece that matched at 31″x48″ so that is in kitchen area. That small area rug did coat another $20 but worth it to ensure the match.  We are really happy with this. Total project time, not including obtaining materials, 1 hr. Total project cost, under $80.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s